![lt1 scanmaster lt1 scanmaster](https://i.ytimg.com/vi/cmZ0-0cqoYA/maxresdefault.jpg)
That might be the problem because I didn't have it customized, the previous owner did about 20 years ago.
![lt1 scanmaster lt1 scanmaster](https://i.ebayimg.com/images/g/ZrAAAOSwKIpWBWIP/s-l400.jpg)
I can't touch the throttle without it hiccupping.
#Lt1 scanmaster pro#
Then when it hit closed, the BLM dropped to 105 and the car crapped out. 1.1 BlueDriver 1.2 OBD Fusion 1.3 DashCommand 1.4 FIXD 1.5 OBDLink 1.6 OBD Auto Doctor 1.7 Torque Pro 1.8 Carista OBD2 1.9 ScanMaster. So I turned the Base to #5 (leaner at idle) and it ran great while in open mode. I got a rich O2 code once it kind of ran for a while. Tried to start the car and it barely worked. Actron CP9695 AutoScanner Pro OBD II Scan Tool for All 1996 and Newer and Select 1994-95 Vehicles - Includes Enhanced Drivetrain, ABS, and SRS Coverage, CodeConnect, and More. After finding instructions that made freaking sense, I turned the Base to #3. I went with the 3" LT1 remanufactured MAF from Kirban. I found a reman stock MAF from Kirban I believe and opted to go with that instead of going to the MAF Translator. My TTA has been running great all these years. I haven't been around these parts in a while. Later or Firefox installed on your computer as well as Acrobat Reader. LTCC LT1 Coil per Cylinder Converter 399.00 Add to cart LTCC replacement harness 150.00 Add to cart LTCC replacement interface unit 250.00 Add to cart MAF Translator for Turbo Buick and 1989 Turbo Trans-Am 199.99 Add to cart Powerlogger for Turbo Buick 264.99 Add to cart Scanmaster 2.1 for Turbo Buick 249.99 Add to cart.
#Lt1 scanmaster how to#
You must have Microsoft Windows 98/ME/2000/XP/7 with Microsoft Internet Explorer 5.01 or Camaro ScanMaster Installation: How to install the Modern Musclecar ScanMaster into the air vent of your Camaro C.A.G.S (skip shift) Disable via the PCM - NO resistor If you have an OBD-I (94 or 95) this is THE way IMO to disable CAGS. MAF Translator for 1986/87 Turbo Buick V6 3. ScanMaster-ELM Minimum Platform and Software Requirements
![lt1 scanmaster lt1 scanmaster](http://brewcitymuscle.com/forum/images/garage/attach/2/0/0/6/garage_vehicle-42-13035217351_thumb.jpg)
Power and Torque Measurement since version 1.9.ĭirect connection methods for USB, Bluetooth® and WLAN interfaces since version 2.0. Shows Fuel Consumption since version 1.3.
#Lt1 scanmaster verification#
Reports vehicle’s continuously monitored emissions-related tests that have failed during a drive cycle and have not matured to indicate a diagnostic trouble code withĭisplays specific information applicable to the vehicle under test (VIN, Calibration ID,Calibration Verification Number, In-Use Performance Tracking). Powertrain control module with “Oxygen Sensors” mode (Mode $05).ĭisplays non-continuous diagnostic test results specific to the vehicle manufacturer (Mode $06 data) with the “Monitoring Tests Results” mode. Review the results of the oxygen sensor testing performed by the vehicle’s I had it on MPH and after about 45min it locked and I couldn't get it to do anything. I did have the gauge lock up on me before during a long drive. Clear all emissions-related diagnostic information. The powerlogger shows normal values and does not drop out in the logs.